Restarting system. NAND:  No NAND device found!!! 0 MiB U-Boot 2008.10 (Nov 21 2011 - 22:54:39) current ddr size 256m === c0000000,10000000 DRAM:  256 MB Flash: 16 MB In:    serial Out:   serial Err:   serial cuurent type u-boot-3515 version 201109060857 current is nvp1104a, will close audio loop not find tw8832  0xff  buf_product_type[0] = 49 USB:   scanning bus for devices... 1 USB Device(s) found 0 Storage Device(s) found Press CTRL-C to abort autoboot in open logo jpeg decoding ... <> <> decode success!!!! start addr color = 0, logo img width 480, height 320 ## Booting kernel from Legacy Image at 80100000 ...    Image Name:   hilinux    Image Type:   ARM Linux Kernel Image (uncompressed)    Data Size:    2047844 Bytes =  2 MB    Load Address: c0800000    Entry Point:  c0800000    Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux.................................................................................................................................. done, booting the kernel. Linux version 2.6.24-rt1-hi3515v100 (root@localhost.localdomain) (gcc version 3.4.3 (release) (CodeSourcery ARM Q3cvs 2004)) #201010220920 Thu Mar 15 03:54:45 EST 2012 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 Machine: hi3515v100 Memory policy: ECC disabled, Data cache writeback CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256 Kernel command line: busclk=220000000 mem=64M console=ttyAMA0,115200 root=1f01 rootfstype=jffs2 mtdparts=physmap-flash.0:3M(boot),13M(rootfs) pcimod=host pciclksel=1 PID hash table entries: 256 (order: 8, 1024 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 60672KB available (3776K code, 335K data, 108K init) Mount-cache hash table entries: 512 HI_VERSION=LINUX_2_6_24-M01C06FB02F @Hi3515v100R001_C_0_0_0 2010-03-16 10:41:14 CPU: Testing write buffer coherency: ok net_namespace: 64 bytes NET: Registered protocol family 16 Hisilicon clock system V0.01 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 Time: hisi_timer1 clocksource has been installed. IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NetWinder Floating Point Emulator V0.97 (double precision) JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. yaffs Jun  4 2010 15:47:34 Installing. io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered (default) io scheduler cfq registered Serial: AMBA PL011 UART driver uart:0: ttyAMA0 at MMIO 0x20090000 (irq = 12) is a AMBA/PL011 console [ttyAMA0] enabled uart:1: ttyAMA1 at MMIO 0x200a0000 (irq = 12) is a AMBA/PL011 uart:2: ttyAMA2 at MMIO 0x200b0000 (irq = 13) is a AMBA/PL011 uart:3: ttyAMA3 at MMIO 0x200c0000 (irq = 13) is a AMBA/PL011 RAMDISK driver initialized: 4 RAM disks of 16384K size 4096 blocksize loop: module loaded PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 PPPoL2TP kernel driver, V1.0 usbcore: registered new interface driver prism54usb Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods SCSI Media Changer driver v0.25 Driver 'ch' needs updating - please use bus_type methods hi3515-ahci-device hi3515-ahci-device.: controller can't do NCQ, turning off CAP_NCQ scsi0 : hi3515-ahci-device scsi1 : hi3515-ahci-device ata1: SATA max UDMA/133 irq 29 ata2: SATA max UDMA/133 irq 29 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-8: WDC WD5000AUDX-63WNHY0, 01.01A01, max UDMA/133 ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/133 ata2: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access     ATA      WDC WD5000AUDX-6 01.0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA  sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 physmap platform flash device: 04000000 at 80000000 physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank  Amd/Fujitsu Extended Query Table at 0x0040 physmap-flash.0: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. 2 cmdlinepart partitions found on MTD device physmap-flash.0 Creating 2 MTD partitions on "physmap-flash.0": 0x00000000-0x00300000 : "boot" 0x00300000-0x01000000 : "rootfs" No NAND device found!!! usbcore: registered new interface driver cdc_acm drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1 drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303 usbcore: registered new interface driver pl2303 drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver mice: PS/2 mouse device common for all mice usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 10 lo: Disabled Privacy Extensions tunl0: Disabled Privacy Extensions Mobile IPv6 IPv6 over IPv4 tunneling driver sit0: Disabled Privacy Extensions NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation VFS: Mounted root (jffs2 filesystem). Freeing init memory: 108K init started:  BusyBox v1.1.2 (2010.03.16-02:37+0000) multi-call binary             _ _ _ _ _ _ _ _ _ _ _ _             \  _  _   _  _ _ ___             / /__/ \ |_/            / __   /  -  _ ___           / /  / /  / /   _ _ _ _/ /  /  \_/  \_ ______ ___________\___\__________________ [RCS]: /etc/init.d/S00devs [RCS]: /etc/init.d/S01udev [RCS]: /etc/init.d/S80network hi3515v100-ehci hi3515v100-ehci.0: hi3515v100-ehci hi3515v100-ehci hi3515v100-ehci.0: new USB bus registered, assigned bus number 1 hi3515v100-ehci hi3515v100-ehci.0: irq 23, io mem 0x100b0000 hi3515v100-ehci hi3515v100-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected hi3515v100-ohci hi3515v100-ohci.0: hi3515v100-ohci hi3515v100-ohci hi3515v100-ohci.0: new USB bus registered, assigned bus number 2 hi3515v100-ohci hi3515v100-ohci.0: irq 22, io mem 0x100a0000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep modprobe: could not parse modules.dep No need to recovery program from USB rm: cannot remove `/mnt/mtd/preupgrade.sh': No such file or directory rm: cannot remove `/mnt/mtd/productcheck': No such file or directory extdrv extdrv/tw2864.ko extdrv/hiether.ko extdrv/encryptgpio.ko extdrv/ds1307.ko extdrv/cryptomemory.ko extdrv/gpio.ko extdrv/fgpio.ko extdrv/wdt.ko extdrv/gpioi2c.ko extdrv/hi_ir.ko extdrv/nvp1104a_3515.ko extdrv/ncdecoder.ko extdrv/hidmac.ko hi3515_adec.ko hi3515_aenc.ko hi3515_ai.ko hi3515_ao.ko hi3515_base.ko hi3515_chnl.ko hi3515_dsu.ko hi3515_group.ko hi3515_h264d.ko hi3515_h264e.ko hi3515_jpegd.ko hi3515_jpege.ko hi3515_md.ko hi3515_sio.ko hi3515_sys.ko hi3515_vdec.ko hi3515_vd.ko hi3515_venc.ko hi3515_viu.ko hi3515_vou.ko hi3515_vpp.ko hifb.ko load3515 sysctl_hi3515.sh tde.ko Hisilicon ETH net controler(ver Aug 11 2010 17:54:13). Hisilicon ETH MDIO Bus: probed Invalid HW-MAC Address: 00:00:00:00:00:00 Set Random MAC address: 8A:5D:F1:BA:6C:FE 64 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x20110104: 0x00009654 --> 0x00009654 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x20110100: 0x00000887 --> 0x00000887 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x2011010c: 0x00000003 --> 0x00000003 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x20110110: 0x00000007 --> 0x00010303 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x20110114: 0x00000007 --> 0x00010303 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x20110118: 0x00010F01 --> 0x00000007 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x2011011c: 0x00010F01 --> 0x00000007 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x20110128: 0x00010020 --> 0x00010020 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x2011012c: 0x000103A2 --> 0x00010601 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x20110130: 0x00000005 --> 0x00010803 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x20110134: 0x00000007 --> 0x00000007 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x20110138: 0x00010804 --> 0x00010804 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x2011013c: 0x00000007 --> 0x00000007 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x20050078: 0x00008002 --> 0x00008002 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x20050054: 0x00004003 --> 0x00001573 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x200f0094: 0x00000001 --> 0x00000001 *** Board tools : ver0.0.1_20060106  *** [debug]: {source/utils/cmdshell.c:166}cmdstr:himm 0x200f0098: 0x00000001 -->Hisilicon Media Memory Zone Manager  0x00000001 current version 256M memory i2c version : 201103071228 current no chip 1108, id = 255 insmod: cannot insert `extdrv/ncdecoder.ko': Operation not permitted (-1): Operation not permitted current chip is nvp1104a 201112291639 norm:2,chips:2,cpu:3515 nvp1004a driver(20100812)  Dec 30 2011,00:05:36 insmod: cannot open module `./extdrv//tlv_aic23.ko': No such file or directory fgpio: module license 'GM License' taints kernel. HISI_IRDA-MF @Hi3520v100R001_C_0_2_0 2009-12-22 19:31:21 hiir: init ok. ver=Mar 30 2010, 11:44:20. Hisilicon Watchdog Timer: 0.01 initialized. default_margin=60 sec (nowayout= 0, nodeamon= 0) HISI_WDT-MDC030001 @Hi3511v110_OSDrv_1_0_0_8 2009-03-30 10:45:48  gpio for test version: 201005261515 TVT 35xx CryptoMemory Device Driver v1.0.0: May  9 2010 06:22:46 hifb info: HIFB_MAIN_VERSION[v1.0.0.2] Build Time[Apr 27 2010, 10:45:15] hifb info: video:vram0_size=1024,vram1_size=16588800,vram2_size=1024,vram3_size=1024,vram4_size=10485760 hifb info: succeed in registering the fb0: ovl0 frame buffer device hifb info: succeed in registering the fb1: ovl1 frame buffer device hifb info: succeed in registering the fb2: ovl2 frame buffer device hifb info: succeed in registering the fb3: ovl3 frame buffer device hifb info: succeed in registering the fb4: ovl4 frame buffer device TDE_MAIN_VERSION[v2.0.0.0] Build Time[Apr 27 2010, 10:45:19] TDE_ADP_VERSION[hi3515adp v2.0.0.0] Build Time[Apr 27 2010, 10:45:19] tde run on master arm tde run for graphic service tde map reg:basePhyAddr:20140000 baseVirAddr:c4898000 size:3000 Hisilicon UMAP device driver interface: v3.00 Chip Version: Hi35150100 load vd.ko ....OK! load vou.ko ....OK! load vdec.ko ....OK load vpp.ko ....OK! load md.ko....OK! load h264d.ko OK ++++++++g_chip_type = 0 2408  rtc Device Driver 201012091052 v1.0.0 ADDRCONF(NETDEV_UP): eth0: link is not ready Auto login as root ... Jan  1 00:00:15 login[615]: root login  on `ttyS000' BusyBox v1.1.2 (2010.03.16-02:37+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands. Welcome to HiLinux. None of nfsroot found in cmdline. ~ $ PUB_common.cpp, 1906, pid = 623, tid=623 xdvr.cpp, 562, pid = 614, tid=614 PHY: 0:01 - Link is Up - 100/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready check OK! LocalDevice.cpp,3754,new crytoinfo #############xdvr.cpp,585,productID:201 productID:201,subProductID:3 xdvr.cpp,605,programeId:3,subProductID:3.xdvr.cpp,638,g_bProIdequeSubProdID:1 ######################xdvr.cpp,657,no change CVBS Resolution hdtype=0 ------------current param type == 1 product Item (Product.cpp,376)from programe ------------current param type == 3 ------------current param type == 8 ------------current param type == 7 ------------current param type == 6 LocalDevice.cpp,3705,GetKeyBoardNameFromFlash:Q9 xdvr.cpp,712,ChangeKeyBoardType keyboardType:0 xdvr.cpp,725,local keyboardtype;0 Intial CLanguagePack succ! ------------current param type == 5 Initial ReadDDdns ok ------------current param type == 4 Inital config manager succ ConfigEx.cpp,2118, first check NCFG_ITEM_ENCODE_MAJOR maxRate:224,totalRate:240  ConfigEx.cpp,2122, no need change NCFG_ITEM_ENCODE_MAJOR ------------current param type == 3 ------------current param type == 8 ##xdvr.cpp,1046,videoout res flash == config check OK! ***==0==***cryptomemory ok ------------current param type == 1026  DVR SDK VERSION : *** 201210231750 *** current alloc buf variant len = 1327384 set default value = 1000 current jiffts value = 1000 alloc m_pb_buf_addr = 40515008, 3145728 alloc m_compress_buf_addr 4081d008, 11534336 all used mem len 15826944 curreset opt 1 nt product 3515 keyboard se 0 alloc var buffer add 402e8de0, len 427492 Current TD2308SE DVR Product Param Init current decode chip number = 2 get current decode chip type 2001 tw2864 select playback audio out set_audio_mix_out ok start vi vo device ...... start vi channel ...... start venc group ...... start venc local ...... start venc net ...... start vdec ...... start tde ...... starthifb info:  vo max resolution w:1024 h:768  framebuf G1 ...... current set fb width 1024, height 768 fb width 1024, height 768, len 16588800, 2048 start framebuf G4 ......hifb info:  vo max resolution w:1024 h:768 current set fb width 32, height 32 fb width 32, height 32, len 10485760, 128 sdvr initialize success thread_route_encode_video_frame, thread id = 628 thread_route_encode_video_local_device, thread id = 629 thread_route_encode_video_net_device, thread id = 630 thread_route_audio_capture, thread id = 631 thread_route_video_playbck, thread id = 632 thread_route_video_pb_local, thread id = 633 thread_route_audio_playback, thread id = 634 thread_rget time is:22-18-08 5 22:02:33 oute_check_other_thread, thread id = 635 thread_route_mouse_process, thread id = 636 thread_route_keyboard_process, thread id = 637 thread_route_ir_process, thread id = 638 thread_route_feed_wdg, thread id = 639 thread_route_capture_jpeg, thread id = 640 thread_route_slave_cpu_check_time, thread id = 641 RTC Time:16-12-8 16:2:21 ##read chip type:8193  is 1104 Initial local device succ! fb w = 1024, h = 768 The mem is :1572864 The line_length is :2048 The xres is :1024 The yres is :768 bits_per_pixel is :16 Font.cpp,87,cd /nfsdir && tar -xzvf /mnt/mtd/ui/ui.tar font.dat font.dat xdvr.cpp, 322, pid = 647, tid = 647 start flash screen. Start flash screen ok! ------------current param type == 0 macflash:00:18:AE:2B:7A:C6 macfile:00:18:AE:2B:7A:C6 ------------current param type == 4 videoflash:0 videofile:0 ------------current param type == 10 Initial message man succ cur language is in language list MainFrame.cpp,84set opt 2 72,start dog MainFrame.cpp,8502,set cset opt 1 hnn:0, waterMack MainFrame.cpp,8502,set chnn:1, waterMack MainFrame.cpp,8502,set chnn:2, waterMack MainFrame.cpp,8502,set chnn:3, waterMack MainFrame.cpp,8502,set chnn:4, waterMack MainFrame.cpp,8502,set chnn:5, waterMack MainFrame.cpp,8502,set chnn:6, waterMack MainFrame.cpp,8502,set chnn:7, waterMack MainFrame.cpp,8505,kill dog Setup warter mark CDOperationMan.cpp,58 Initial CD-Rom man succ dvrId:0018ae2b7ac60000 ######/dev/sda mknod: /dev/sda: File exists mknod /dev/sda b 8 0 CMD : mknod /dev/sda b 8 0 execute fail mknod: /dev/sda1: File exists mknod /dev/sda1 b 8 1 CMD : mknod /dev/sda1 b 8 1 execute fail mknod: /dev/sda2: File exists mknod /dev/sda2 b 8 2 CMD : mknod /dev/sda2 b 8 2 execute fail mknod: /dev/sda3: File exists mknod /dev/sda3 b 8 3 CMD : mknod /dev/sda3 b 8 3 execute fail mknod: /dev/sda4: File exists mknod /dev/sda4 b 8 4 CMD : mknod /dev/sda4 b 8 4 execute fail mkdir -p /mnt/00 mkdir -p /mnt/01 mkdir -p /mnt/02 mkdir -p /mnt/03 umount: Couldn't umount /mnt/00: Invalid argument CMD : umount /mnt/00 execute fail mount -t vfat /dev/sda1 /mnt/00  successed umount: Couldn't umount /mnt/01: Invalid argument CMD : umount /mnt/01 execute fail mount -t vfat /dev/sda2 /mnt/01  successed umount: Couldn't umount /mnt/02: Invalid argument CMD : umount /mnt/02 execute fail mount -t vfat /dev/sda3 /mnt/02  successed umount: Couldn't umount /mnt/03: Invalid argument CMD : umount /mnt/03 execute fail mount -t vfat /dev/sda4 /mnt/03  successed ########szTmp:rm -rf /mnt/00/HtmlData/* open /mnt/00/PictMan.dat ok open /mnt/00/reclog.bin ok open /mnt/00/eventlog.bin ok open /mnt/00/operlog.bin ok open /mnt/00/diskver ok ########szTmp:rm -rf /mnt/01/HtmlData/* open /mnt/01/PictMan.dat ok open /mnt/01/reclog.bin ok open /mnt/01/eventlog.bin ok open /mnt/01/operlog.bin ok open /mnt/01/diskver ok ########szTmp:rm -rf /mnt/02/HtmlData/* open /mnt/02/PictMan.dat ok open /mnt/02/reclog.bin ok open /mnt/02/eventlog.bin ok open /mnt/02/operlog.bin ok open /mnt/02/diskver ok ########szTmp:rm -rf /mnt/03/HtmlData/* open /mnt/03/PictMan.dat ok open /mnt/03/reclog.bin ok open /mnt/03/eventlog.bin ok open /mnt/03/operlog.bin ok open /mnt/03/diskver ok /mnt/00 === /dev/sda /mnt/01 === /dev/sda /mnt/02 === /dev/sda /mnt/03 === /dev/sda Initial diskmanager succ Initial reclog manager succ add disk path = /mnt/00/PictMan.dat add disk path = /mnt/01/PictMan.dat add disk path = /mnt/02/PictMan.dat add disk path = /mnt/03/PictMan.dat Initial log manager succ MainFrame.cpp,428,prerecordStartIndex:0,prerecordParNum:4,pDiskPath:/mnt Inital record manager succ Initial smtp manager succ Initial m_pSnapPictureMan manager succ Inital stream proc succ Inital data server proc succ Inital netReader succ Initial backupman succ Initial smtp manager succ Initial alarm out manager succ Initial motion manager succ Initial sensor in manager succ Initial video loss manager succ Initial video loss manager succ Initial alarm manager succ Initial ptz manager succ Initial fake curise succ Initial pinyin input succ Initial display man succ Initial UpnpMan man succ Initial config set manager succ Initial():MainFrame.cpp:770, initial the alloc NIC IP succ Initial():MainFrame.cpp:794, initial the DDNS manager succ ReclogManEx.cpp,1214,diskSize:128 @@@@@@ConfigSetMan.cpp,684, Initial CMessageMan::Instance()->SetChannelVisible:1 @@@@@@ConfigSetMan.cpp,685, Initial m_pLocalDeviceMan->SetCamVisible:1 set chnn:00 local rate:7, encode:1, bitstream:1024, quality:5 set chnn:01 local rate:7, encode:1, bitstream:1024, quality:5 set chnn:02 local rate:7, encode:1, bitstream:1024, quality:5 set chnn:03 local rate:7, encode:1, bitstream:1024, quality:5 set chnn:04 local rate:7, encode:1, bitstream:1024, quality:5 set chnn:05 local rate:7, encode:1, bitstream:1024, quality:5 set chnn:06 local rate:7, encode:1, bitstream:1024, quality:5 set chnn:07 local rate:7, encode:1, bitstream:1024, quality:5 set chnn:00 net    rate:3, encode:2, bitstream:512, quality:5 set chnn:01 net    rate:3, encode:2, bitstream:512, quality:5 set chnn:02 net    rate:3, encode:2, bitstream:512, quality:5 set chnn:03 net    rate:3, encode:2, bitstream:512, quality:5 set chnn:04 net    rate:3, encode:2, bitstream:512, quality:5 set chnn:05 net    rate:3, encode:2, bitstream:512, quality:5 set chnn:06 net    rate:3, encode:2, bitstream:512, quality:5 set chnn:07 net    rate:3, encode:2, bitstream:512, quality:5 ConfigSetMan.cpp,2412,NCFG_ITEM_JPEG_PERIOD:2 ConfigSetMan.cpp,2419,NCFG_ITEM_JPEG_SIZE:2 ConfigSetMan.cpp,2445,NCFG_ITEM_JPEG_QUALITY:5 ==> 2 ConfigSetMan.cpp,2453,NCFG_ITEM_JPEG_SNAP_NUM:3 ########SmtpMan.cpp,534,m_snapImgNum:3 Dec  8 16:02:27 udhcpc[713]: udhcpc (v0.9.9-pre) started Dec  8 16:02:27 udhcpc[713]: Sending discover... Dec  8 16:02:27 udhcpc[713]: Sending select for 192.168.14.19... Dec  8 16:02:27 udhcpc[713]: Lease of 192.168.14.19 obtained, lease time 43200 route: SIOC[ADD|DEL]RT: No such process route: SIOC[ADD|DEL]RT: File exists CMD : route add -net 224.0.0.0 netmask 240.0.0.0 dev eth0 execute fail route: SIOC[ADD|DEL]RT: File exists ########SmtpMan.cpp,550,m_bSnapImg:1 CMD : route add -net 224.0.0.0 netmask 240.0.0.0 dev eth0 execute fail EffecCruiseCfg:ConfigSetMan.cpp:2574, set the curise EffecCruiseCfg:ConfigSetMan.cpp:2574, set the curise EffecCruiseCfg:ConfigSetMan.cpp:2574, set the curise EffecCruiseCfg:ConfigSetMan.cpp:2574, set the curise EffecCruiseCfg:ConfigSetMan.cpp:2574, set the curise EffecCruiseCfg:ConfigSetMan.cpp:2574, set the curise EffecCruiseCfg:ConfigSetMan.cpp:2574, set the curise EffecCruiseCfg:ConfigSetMan.cpp:2574, set the curise Setup config succ Initial main frame succ disknum=1 ------------current param type == 1 Initial network Server succ xdvr.cpp,1728,host:192.168.14.22,dwPort:10002,ID:382 Initial Web Server succ ~ $ SetExKeyboardType:ExternalKeyboard.cpp:106, The external 485 keyboard is TVT_MY1003 ExternalKeyboard.cpp, 136, pid = 734, tid=734 Start device succ MainFrame.cpp, 1621, pid = 735, tid=735 entry while clear buf ............ RecordMan.cpp, 989, pid = 737, tid=737 DVRTimer.cpp, 198, Timer thread pid = 736, tid=736 end while clear buf ............  clear buffer ------------------ end StreamProc.cpp,271,PUB_CreateThreadEx(StreamThread, (void *)this, &m_bStream, 50); StreamProc.cpp, 624, pid = 738, tid=738 Start:MainFrame.cpp:1287, Start upnpMan sucss Start main frame succ set chnn:00 local rate:7, encode:1, bitstream:1024, quality:5 set chnn:01 local rate:7, encode:1, bitstream:1024, quality:5 set chnn:02 local rate:7, encodset opt 2 e:1, bitstream:1024, quality:5 set chnn:03 local rate:7, encode:1, bitstream:1024, quality:5 StreamProc.cpp, 1300, pid = 740, tid=740 DdnsManager.cpp, 499, pid = 748, tid=748 MainFrame.cpp, 8037, timer pid = 749, tid = 749 SmtpMan.cpp,1141,SendMailThread pid=743, tid=743 DataSerProc.cpp, 125, pid = 741, tid=741 UpnpMan.cpp 453 upnp man pid = 753 MainFrame.cpp, 8395, pid = 751, tid=751 MainFrame.cpp, 8112, pid = 750, tid=750 AlarmMan.cpp, 269, pid = 746, tid=746 NetReader.cpp, 568, pid = 742, tid=742 StreamProc.cpp, 853, pid = 739, tid=739 DisplayMan.cpp, 1765, pid = 747, tid=747 MainFrame.cpp, 7920, feed dog pid = 752, tid=752 FakeCurise.cpp, 242, pid = 744, tid=744 AlarmMan.cpp, 133, pid = 745, tid=745 set chnn:04 local rate:7, encode:1, bitstream:1024, quality:5 set chnn:05 local rate:7, encode:1, bitstream:1024, quality:5 set chnn:06 local rate:7, encode:1, bitstream:1024, quality:5 set chnn:07 local rate:7, encode:1, bitstream:1024, quality:5 NetServer.cpp, 899, pid = 754, tid=754 SWL_MultiNetComm.cpp, 620, pid = 755, tid=755 SWL_ListenProcEx.cpp, 137, pid = 756, tid=756 NetServer.cpp, 730, pid = 757, tid=757 NetServer.cpp, 2596, pid = 758, tid=758 Start network Server succ StreamProc.cpp,555,m_secondLimitRateForFirstStreamNum:-1,m_secondLimitAllRateForFirstStreamNum:-1 StreamProc.cpp,1652, maxCopies:40,m_secondRateLimit:-1 StreamProc.cpp,1658, m_secondSendAllNum:0,maxCopies:40 set chnn:00 net    rate:1, encode:2, bitstream:512, quality:5 set chnn:01 net    rate:1, encode:2, bitstream:512, quality:5 set chnn:02 net    rate:1, encode:2, bitstream:512, quality:5 set chnn:03 net    rate:1, encode:2, bitstream:512, quality:5 set chnn:04 net    rate:1, encode:2, bitstream:512, quality:5 set chnn:05 net    rate:1, encode:2, bitstream:512, quality:5 set chnn:06 net    rate:1, encode:2, bitstream:512, quality:5 set chnn:07 net    rate:1, encode:2, bitstream:512, quality:5 check OK! ---------------------------new connection established ---------------------------new connection established ------------current param type == 1 SWL_MultiNetComm.cpp 600 : Connection reset by peer ▒Է▒socket▒ѶϿ▒▒▒116-11-8 13:2:33 MainFrame.cpp,1700,g_bProIdequeSubProdID:1 ------------current param type == 1 ###@@@@@@@@@@@#######Product.cpp,13987, kernelVersion:1111220355-1203150855-, hardwareVersion:201.3.4.Q9-1.03, MCUVersion:---, mac:018ae2b7ac6 NetServer.cpp, 1066 current hardware version : 1.03 len : 4 ##############MainFrame.cpp,8020, SetLcdScreemStatus:1 UserMan.cpp,450,ChangeSecondStreamCH:allsendnum:1 StreamProc.cpp,555,m_secondLimitRateForFirstStreamNum:-1,m_secondLimitAllRateForFirstStreamNum:-1 StreamProc.cpp,1652, maxCopies:40,m_secondRateLimit:-1 StreamProc.cpp,1658, m_secondSendAllNum:1,maxCopies:40 StreamProc.cpp,1693,m_secondSendAllNum:1,maxrate:30,maxrateTemp:30 set chnn:00 net    rate:24, encode:2, bitstream:512, quality:5 set chnn:01 net    rate:1, encode:2, bitstream:512, quality:5 set chnn:02 net    rate:1, encode:2, bitstream:512, quality:5 set chnn:03 net    rate:1, encode:2, bitstream:512, quality:5 set chnn:04 net    rate:1, encode:2, bitstream:512, quality:5 set chnn:05 net    rate:1, encode:2, bitstream:512, quality:5 set chnn:06 net    rate:1, encode:2, bitstream:512, quality:5 set chnn:07 net    rate:1, encode:2, bitstream:512, quality:5 1761 xdvr Start local window succ ------------current param type == 1 ###@@@@@@@@@@@#######Product.cpp,13987, kernelVersion:1111220355-1203150855-, hardwareVersion:201.3.4.Q9-1.03, MCUVersion:---, mac:018ae2b7ac6 ---------------------------new connection established MainFrame.cpp,1700,g_bProIdequeSubProdID:1 ###@@@@@@@@@@@#######Product.cpp,13987, kernelVersion:1111220355-1203150855-, hardwareVersion:201.3.4.Q9-1.03, MCUVersion:---, mac:018ae2b7ac6 NetServer.cpp, 1066 LocalDevice.cpp,1220, ext_set_voutdev_color,br:160,co:139,sa:142,hu:126 LocalUIMan.cpp, 260, pid = 778, tid=778 xdvr.cpp, 540, pid = 647, end flash screen. Stop flash screen! webserver.cpp, 1325, pid = 779, tid=779 webserver.cpp, 1436, pid = 780, tid=780 webserver.cpp, 1174, pid = 781, tid=781 Start Web Server succ LocalDevice.cpp,960,open chnn:0 live audio,ok setAudioAuto:1 Set do dwell enable=0.